M22×65 Track Shoe Bolt & Nut: Dimensions, Fitment, and Replacement Guide

An M22×65 track shoe bolt is identified by a nominal thread diameter of 22 mm and a stated bolt length of 65 mm. Those two figures are useful for screening, but they are not enough by themselves to confirm fitment: buyers also need to verify thread pitch, head and neck geometry, washer requirements, nut style, and the machine’s parts specification. I recommend comparing the existing fastener or its part number with the machine or undercarriage documentation before placing an order. This guide explains what to check, how to replace the assembly, and what to provide when requesting a quotation from Zhonghai Jiuchuan.

You can find more information on our web, so please take a look.

Key Takeaways

• M22 indicates a nominal thread diameter of 22 mm; confirm the thread pitch rather than assuming it.
• 65 mm is the stated bolt length, but confirm the measurement convention and required grip length for the specific bolt design.
• Fitment depends on the complete assembly: bolt head and neck, track shoe and link, nut, and any specified washer or locking feature.
• Use the equipment manufacturer’s service instructions for tightening sequence and torque; do not apply a generic value.
• For a sourcing enquiry, share the machine or undercarriage details, part number, sample dimensions, quantity, and delivery requirements.

Who This Guide Is For

This guide is for parts distributors, fleet maintenance teams, equipment repair businesses, and procurement professionals sourcing track shoe fasteners. It is especially relevant when replacing worn, damaged, or missing bolts and nuts, or when checking whether an offered M22×65 assembly matches an existing application. The information supports initial screening and purchase discussions, but it does not replace the machine manufacturer’s parts catalogue or service procedure. If the original specification is unclear, confirm it with the equipment supplier or a qualified undercarriage technician before installation.

Understanding the M22×65 Designation

What the numbers tell you

In a metric fastener designation, “M22” refers to a nominal thread diameter of 22 mm. The “65” commonly describes a bolt length of 65 mm, but the exact reference points can depend on the bolt’s head design and the supplier’s drawing or standard. For many fasteners, length is measured from beneath the head to the end of the bolt; do not rely on that convention without checking the product drawing. The designation does not state thread pitch, bolt grade, head dimensions, or nut specification.

Materials, grades, and finishes

Track shoe fasteners are offered in different material and mechanical-property specifications, and the appropriate option depends on the equipment design and operating conditions. A product description that gives only “M22×65” does not establish the bolt’s grade, heat treatment, hardness, or coating. Ask for the applicable specification or drawing and confirm that the nut is compatible with the bolt. Avoid substituting a general-purpose fastener based only on matching diameter and length.

How to Check Fitment Before Ordering

Use the machine specification first

Start with the machine make, model, serial or product identification details, and the undercarriage or track shoe part number. Check the applicable parts catalogue or service documentation for the required fastener reference. If a catalogue lists a complete bolt-and-nut assembly, confirm whether washers or other components are included or specified separately. This information helps a supplier distinguish between fasteners that appear similar but differ in geometry or specification.

Inspect and measure the existing assembly

If the original part is available, clean it sufficiently to inspect the threads, head, neck, bearing surface, and nut. Measure the bolt length using the same reference points shown on the supplier drawing, and use a suitable thread gauge or confirmed technical reference to establish the pitch. Compare the head profile and neck dimensions with the replacement drawing, rather than checking only the threaded portion. If the old fastener is badly worn or deformed, treat its measurements as a reference rather than definitive proof of the required specification.

Zhonghai Jiuchuan contains other products and information you need, so please check it out.

Check the mating parts

Inspect the track shoe and track link for damaged holes, burrs, cracks, distortion, or embedded debris. A new bolt may not seat correctly if the mating surfaces are damaged or contaminated. Confirm that the bolt head sits in its intended position and that the nut can engage as designed without interference. Where the machine documentation specifies a particular assembly orientation or locking method, follow that instruction.

Replacement Process

1. Confirm the replacement specification. Match the part number or drawing and verify diameter, pitch, length, head and neck geometry, nut type, and any specified washers.
2. Prepare the equipment safely. Park and secure the machine according to its service procedure, and use suitable lifting, blocking, and personal protective equipment. Track components are heavy; use trained personnel and approved handling methods.
3. Remove the old assembly. Follow the equipment manufacturer’s procedure and use suitable tools. If a fastener is seized or damaged, use an approved removal method that does not compromise the track shoe or link.
4. Inspect and clean the joint. Check the mating holes and contact surfaces, removing loose contamination without altering the specified fit or surface.
5. Install the correct bolt and nut. Position the bolt in the specified orientation and fit the matching nut and any required components. Start the threads carefully to avoid cross-threading.
6. Tighten to the documented requirement. Follow the manufacturer’s sequence and torque procedure using suitable tooling. Do not substitute a generic torque value, because the correct requirement can depend on the fastener and machine specification.
7. Complete the prescribed inspection. Carry out any recheck or follow-up inspection required by the service documentation and record the part reference used.

Common Fitment and Replacement Mistakes

• Ordering by diameter and length alone: M22 and 65 mm do not identify pitch, head style, neck dimensions, grade, or nut configuration.
• Assuming all M22 threads are interchangeable: Confirm pitch and thread compatibility from a reliable specification or measurement.
• Using an unverified torque value: Obtain the tightening requirement and sequence from the applicable equipment documentation.
• Reusing a damaged mating component: Inspect the shoe and link so that a fastener replacement does not conceal a fit or condition problem.
• Mixing bolt and nut specifications: Source a matched assembly or verify compatibility through the specified technical data.

Buyer Selection and Sourcing Framework

Information to include in a quotation request

A complete enquiry makes it easier to assess fitment and compare offers on an equivalent basis. Include the equipment make and model, machine identification details where available, track shoe or fastener part number, required quantity, and destination. Attach clear photographs and a drawing or measurement sheet if the original specification is uncertain. State whether you need bolts and nuts together and whether the order has packaging, marking, or delivery requirements.

Price, MOQ, and lead time

Pricing can depend on the confirmed specification, material and property requirements, finish, order quantity, packaging, and shipping destination. Minimum order quantities and lead times are supplier- and order-specific, so request them with the quotation rather than relying on a general estimate. Ask whether the quoted price covers the bolt only or a complete bolt-and-nut set, and clarify any separate charges. Comparing quotations is most useful when every supplier is working from the same drawing, part reference, and quantity.

Supplier evaluation checklist

• Can the supplier confirm the full drawing or specification, including thread pitch and head or neck dimensions?
• Can the supplier identify the material or mechanical-property requirements being offered?
• Does the quotation clearly state whether the nut and any required components are included?
• Can the supplier provide available inspection or product documentation relevant to the order?
• Are quantity, MOQ, production or dispatch timing, packaging, and delivery terms stated clearly?

How Zhonghai Jiuchuan Can Support Your Enquiry

At Zhonghai Jiuchuan, we support B2B enquiries for track shoe bolt and nut sourcing by reviewing the application details and the specification provided. To help us assess an M22×65 request, send the machine or undercarriage identification, any part number or drawing, the required quantity, and clear images or measurements of the original assembly. We can then clarify which specification details need confirmation before discussing availability, commercial terms, and delivery arrangements. Where information is incomplete, we recommend resolving fitment questions before production or order confirmation.

Conclusion: Confirm the Complete Assembly Before Replacement

An M22×65 track shoe bolt and nut is a useful starting description, not a complete fitment specification. Confirm the 22 mm nominal thread diameter and 65 mm stated length, then verify pitch, length measurement convention, head and neck geometry, nut type, material or property requirements, and the machine’s installation procedure. Use the equipment documentation for tightening requirements and inspect the mating shoe and link during replacement. For your next step, send Zhonghai Jiuchuan the machine details, part reference or drawing, quantity, and delivery destination so we can review the enquiry against the information available.

The company is the world’s best M22×65 Track Shoe Bolt & Nut supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.